Altec Lansing 950-8A
Best box: 194.5 L bass reflex tuned to 39.1 Hz · F3 39.5 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Altec Lansing 950-8A against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 15.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Altec Lansing 950-8A does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Large enclosure volume (194.5 L) requires extensive internal matrix bracing to prevent panel resonance.
- Limited linear excursion (Xmax: 3.302 mm); set a high-pass subsonic filter at 25–30 Hz when driven with high power.
Recommended Bass Reflex (Vented)
PORT BUILDABLE| Net Box Volume (Vb) | 194.5 Liters |
| Tuning Frequency (Fb) | 39.1 Hz |
| F3 (-3 dB Cutoff) | 39.5 Hz |
| F6 / F10 Extension | 35.0 Hz / 30.5 Hz |
| Port Inner Diameter | Ø 12.5 cm |
| Port Physical Length | 3.4 cm |
| First Pipe Resonance | 5010.0 Hz |
| Estimated MOL @ F3 | 121.7 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 90.2 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 67.8 Hz |
| F3 (-3 dB Cutoff) | 69.5 Hz |
| F6 / F10 Extension | 52.3 Hz / 39.3 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 31.5 Hz |
| Total Q (Qts) | 0.3 |
| Electrical Q (Qes) | 0.31 |
| Mechanical Q (Qms) | 9.07 |
| Equivalent Volume (Vas) | 410.6 Liters |
| Diaphragm Area (Sd) | 858.6 cm² |
| DC Resistance (Re) | 7.0 Ω |
| Efficiency Bandwidth Product (EBP) | 101.5 |
| Linear Excursion (Xmax) | 3.3 mm |
| Thermal Power (Pe) | N/A W |
| Nominal Diameter | 15.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Altec Lansing 950-8A?
Load Forge's calculated alignment puts Altec Lansing 950-8A in a 194.5 liter vented enclosure tuned to 39.1 Hz, reaching an F3 cutoff of approximately 39.5 Hz.
Can Altec Lansing 950-8A be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 90.2 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 69.5 Hz.
What port dimensions should be used for Altec Lansing 950-8A to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 12.5 cm with a length of 3.4 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if 950-8A fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space