B2 Audio Rage XL 18
Best box: 150.0 L bass reflex tuned to 27.0 Hz · F3 25.8 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the B2 Audio Rage XL 18 against your space and targets — instant, no sign-up.
Estimated retail 750.00 USD · Check price & availability ↗
Free, no sign-up to simulate · a free account saves your design
Comparable 18.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the B2 Audio Rage XL 18 does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- The textbook alignment (150.0 L at 21.6 Hz) would need a 124.1 cm port; the recommendation is retuned to 150.0 L at 27.0 Hz so the port can be built.
- Port length (94.7 cm) exceeds a straight internal run; use an elbow bend, slotted vent or 3D folded duct to fit the enclosure.
- Large enclosure volume (150.0 L) requires extensive internal matrix bracing to prevent panel resonance.
Recommended Bass Reflex (Vented)
PORT NEEDS ELBOW / 3D| Net Box Volume (Vb) | 150.0 Liters |
| Tuning Frequency (Fb) | 27.0 Hz |
| F3 (-3 dB Cutoff) | 25.8 Hz |
| F6 / F10 Extension | 22.7 Hz / 20.1 Hz |
| Port Inner Diameter | Ø 22.7 cm |
| Port Physical Length | 94.7 cm |
| First Pipe Resonance | 182.0 Hz |
| Estimated MOL @ F3 | 122.4 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 153.3 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 37.9 Hz |
| F3 (-3 dB Cutoff) | 38.6 Hz |
| F6 / F10 Extension | 29.1 Hz / 22.0 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 30.0 Hz |
| Total Q (Qts) | 0.55 |
| Electrical Q (Qes) | 0.597 |
| Mechanical Q (Qms) | 7.0 |
| Equivalent Volume (Vas) | 100.0 Liters |
| Diaphragm Area (Sd) | 1210.0 cm² |
| DC Resistance (Re) | 1.0 Ω |
| Efficiency Bandwidth Product (EBP) | 50.3 |
| Linear Excursion (Xmax) | 34.0 mm |
| Thermal Power (Pe) | 3500.0 W |
| Nominal Diameter | 18.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for B2 Audio Rage XL 18?
Load Forge's calculated alignment puts B2 Audio Rage XL 18 in a 150.0 liter vented enclosure tuned to 27.0 Hz, reaching an F3 cutoff of approximately 25.8 Hz.
Can B2 Audio Rage XL 18 be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 153.3 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 38.6 Hz.
What port dimensions should be used for B2 Audio Rage XL 18 to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 22.7 cm with a length of 94.7 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if Rage XL 18 fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space