Dayton Audio RS52AN-8
Best box: 0.13 L sealed · Fc 482.2 Hz · F3 394.7 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Dayton Audio RS52AN-8 against your space and targets — instant, no sign-up.
Estimated retail 62.95 EUR · Check price & availability ↗
Free, no sign-up to simulate · a free account saves your design
Comparable 2.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Dayton Audio RS52AN-8 does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Limited linear excursion (Xmax: 1.0 mm); set a high-pass subsonic filter at 25–30 Hz when driven with high power.
Textbook Bass Reflex — not recommended (15.4 dB bass hump)
PORT BUILDABLE| Net Box Volume (Vb) | 1.5 Liters |
| Tuning Frequency (Fb) | 289.8 Hz |
| F3 (-3 dB Cutoff) | 267.8 Hz |
| F6 / F10 Extension | 254.9 Hz / 239.0 Hz |
| Port Inner Diameter | Ø 6.8 cm |
| Port Physical Length | 3.8 cm |
| First Pipe Resonance | 4551.0 Hz |
| Estimated MOL @ F3 | 109.7 dB SPL |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 0.86 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 1.216; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 0.13 Liters |
| System Q (Qtc) | 1.216 (above Butterworth: Qtc cannot fall below Qts (0.86)) |
| System Resonance (Fc) | 482.2 Hz |
| F3 (-3 dB Cutoff) | 394.7 Hz |
| F6 / F10 Extension | 333.6 Hz / 272.5 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 341.0 Hz |
| Total Q (Qts) | 0.86 |
| Electrical Q (Qes) | 1.182 |
| Mechanical Q (Qms) | 3.16 |
| Equivalent Volume (Vas) | 0.1 Liters |
| Diaphragm Area (Sd) | 26.4 cm² |
| DC Resistance (Re) | 6.0 Ω |
| Efficiency Bandwidth Product (EBP) | 288.6 |
| Linear Excursion (Xmax) | 1.0 mm |
| Thermal Power (Pe) | 60.0 W |
| Nominal Diameter | 2.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Dayton Audio RS52AN-8?
A simple ported box is not recommended for Dayton Audio RS52AN-8: the textbook alignment (1.5 liters tuned to 289.8 Hz) needs a 3.8 cm port, and no nearby retune stays buildable without a bass hump. A sealed box, a passive radiator or a folded duct is the practical choice.
Can Dayton Audio RS52AN-8 be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 0.13 liters with a Qtc of 1.216 (above Butterworth: Qtc cannot fall below Qts (0.86)), the system exhibits an F3 of 394.7 Hz.
What port dimensions should be used for Dayton Audio RS52AN-8 to avoid port chuffing?
A straight 6.8 cm port would need 3.8 cm of length, which does not fit a practical cabinet. Use a passive radiator or a folded/3D duct instead of a straight tube.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if RS52AN-8 fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space