Focal SUB 10 DUAL a doppia bobina
Best box: 49.0 L sealed · Fc 35.4 Hz · F3 30.1 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Focal SUB 10 DUAL a doppia bobina against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 9.8" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Focal SUB 10 DUAL a doppia bobina does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Xmax is not published, so the port size is an empirical estimate (area ≥ 12 in² per ft³ of net volume, minimum by driver size), not a displacement calculation. Check air velocity in Load Forge Studio.
- Straight vent would be 199.9 cm long: not physically buildable as a simple tube. Use a passive radiator, a folded slot port or model a 3D folded duct in Load Forge Studio.
Textbook Bass Reflex — not recommended
PORT NOT BUILDABLE| Net Box Volume (Vb) | 39.2 Liters |
| Tuning Frequency (Fb) | 21.2 Hz |
| F3 (-3 dB Cutoff) | 33.9 Hz |
| F6 / F10 Extension | 29.6 Hz / 24.2 Hz |
| Port Inner Diameter ESTIMATED | Ø 12.5 cm |
| Port Physical Length | 199.9 cm |
| First Pipe Resonance | 86.0 Hz |
| Estimated MOL @ F3 | 106.7 dB SPL |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 0.654 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 0.925; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 49.0 Liters |
| System Q (Qtc) | 0.925 (above Butterworth) |
| System Resonance (Fc) | 35.4 Hz |
| F3 (-3 dB Cutoff) | 30.1 Hz |
| F6 / F10 Extension | 26.2 Hz / 22.0 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 25.0 Hz |
| Total Q (Qts) | 0.654 |
| Electrical Q (Qes) | 0.748 |
| Mechanical Q (Qms) | 5.21 |
| Equivalent Volume (Vas) | 49.0 Liters |
| Diaphragm Area (Sd) | 314.0 cm² |
| DC Resistance (Re) | 3.5 Ω |
| Efficiency Bandwidth Product (EBP) | 33.4 |
| Linear Excursion (Xmax) | N/A mm |
| Thermal Power (Pe) | 250.0 W |
| Nominal Diameter | 9.8" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Focal SUB 10 DUAL a doppia bobina?
A simple ported box is not recommended for Focal SUB 10 DUAL a doppia bobina: the textbook alignment (39.2 liters tuned to 21.2 Hz) needs a 199.9 cm port, and no nearby retune stays buildable without a bass hump. A sealed box, a passive radiator or a folded duct is the practical choice.
Can Focal SUB 10 DUAL a doppia bobina be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 49.0 liters with a Qtc of 0.925 (above Butterworth), the system exhibits an F3 of 30.1 Hz.
What port dimensions should be used for Focal SUB 10 DUAL a doppia bobina to avoid port chuffing?
A straight 12.5 cm port would need 199.9 cm of length, which does not fit a practical cabinet. Use a passive radiator or a folded/3D duct instead of a straight tube.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if SUB 10 DUAL a doppia bobina fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space