NVX XQS3v2
Best box: 1.5 L bass reflex tuned to 127.5 Hz · F3 119.0 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the NVX XQS3v2 against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 3.5" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the NVX XQS3v2 does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Xmax is not published, so the port size is an empirical estimate (area ≥ 12 in² per ft³ of net volume, minimum by driver size), not a displacement calculation. Check air velocity in Load Forge Studio.
Recommended Bass Reflex (Vented)
PORT BUILDABLE| Net Box Volume (Vb) | 1.5 Liters |
| Tuning Frequency (Fb) | 127.5 Hz |
| F3 (-3 dB Cutoff) | 119.0 Hz |
| F6 / F10 Extension | 105.2 Hz / 94.9 Hz |
| Port Inner Diameter ESTIMATED | Ø 5.0 cm |
| Port Physical Length | 20.6 cm |
| First Pipe Resonance | 837.0 Hz |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 0.803 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 1.136; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 0.59 Liters |
| System Q (Qtc) | 1.136 (above Butterworth: Qtc cannot fall below Qts (0.80)) |
| System Resonance (Fc) | 212.1 Hz |
| F3 (-3 dB Cutoff) | 176.3 Hz |
| F6 / F10 Extension | 148.5 Hz / 120.9 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 150.0 Hz |
| Total Q (Qts) | 0.803 |
| Electrical Q (Qes) | 0.959 |
| Mechanical Q (Qms) | 4.94 |
| Equivalent Volume (Vas) | 0.6 Liters |
| Diaphragm Area (Sd) | 31.0 cm² |
| DC Resistance (Re) | 3.2 Ω |
| Efficiency Bandwidth Product (EBP) | 156.4 |
| Linear Excursion (Xmax) | N/A mm |
| Thermal Power (Pe) | N/A W |
| Nominal Diameter | 3.5" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for NVX XQS3v2?
Load Forge's calculated alignment puts NVX XQS3v2 in a 1.5 liter vented enclosure tuned to 127.5 Hz, reaching an F3 cutoff of approximately 119.0 Hz.
Can NVX XQS3v2 be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 0.59 liters with a Qtc of 1.136 (above Butterworth: Qtc cannot fall below Qts (0.80)), the system exhibits an F3 of 176.3 Hz.
What port dimensions should be used for NVX XQS3v2 to avoid port chuffing?
Xmax is not published for NVX XQS3v2, so the port is an empirical estimate: a 5.0 cm diameter with a length of 20.6 cm (area at least 12 in² per ft³ of net volume). Check the air velocity at your power level in Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if XQS3v2 fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space