Oberton 15XL700
Best box: 45.5 L bass reflex tuned to 59.8 Hz · F3 63.0 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Oberton 15XL700 against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 15.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Oberton 15XL700 does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
Recommended Bass Reflex (Vented)
PORT BUILDABLE| Net Box Volume (Vb) | 45.5 Liters |
| Tuning Frequency (Fb) | 59.8 Hz |
| F3 (-3 dB Cutoff) | 63.0 Hz |
| F6 / F10 Extension | 55.0 Hz / 47.6 Hz |
| Port Inner Diameter | Ø 15.0 cm |
| Port Physical Length | 21.8 cm |
| First Pipe Resonance | 788.0 Hz |
| Estimated MOL @ F3 | 122.1 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 21.8 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 108.0 Hz |
| F3 (-3 dB Cutoff) | 105.8 Hz |
| F6 / F10 Extension | 80.7 Hz / 61.0 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 45.2 Hz |
| Total Q (Qts) | 0.28 |
| Electrical Q (Qes) | 0.288 |
| Mechanical Q (Qms) | 10.07 |
| Equivalent Volume (Vas) | 117.0 Liters |
| Diaphragm Area (Sd) | 829.6 cm² |
| DC Resistance (Re) | 5.3 Ω |
| Efficiency Bandwidth Product (EBP) | 157.1 |
| Linear Excursion (Xmax) | 8.8 mm |
| Thermal Power (Pe) | 700.0 W |
| Nominal Diameter | 15.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Oberton 15XL700?
Load Forge's calculated alignment puts Oberton 15XL700 in a 45.5 liter vented enclosure tuned to 59.8 Hz, reaching an F3 cutoff of approximately 63.0 Hz.
Can Oberton 15XL700 be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 21.8 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 105.8 Hz.
What port dimensions should be used for Oberton 15XL700 to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 15.0 cm with a length of 21.8 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if 15XL700 fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space