PowerBass M-1204
Best box: 93.0 L bass reflex tuned to 23.5 Hz · F3 22.5 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the PowerBass M-1204 against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 12.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the PowerBass M-1204 does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
Recommended Bass Reflex (Vented)
PORT BUILDABLE| Net Box Volume (Vb) | 93.0 Liters |
| Tuning Frequency (Fb) | 23.5 Hz |
| F3 (-3 dB Cutoff) | 22.5 Hz |
| F6 / F10 Extension | 19.9 Hz / 17.7 Hz |
| Port Inner Diameter | Ø 7.5 cm |
| Port Physical Length | 20.4 cm |
| First Pipe Resonance | 842.0 Hz |
| Estimated MOL @ F3 | 108.9 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 57.8 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 41.8 Hz |
| F3 (-3 dB Cutoff) | 44.4 Hz |
| F6 / F10 Extension | 32.5 Hz / 24.1 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 29.5 Hz |
| Total Q (Qts) | 0.491 |
| Electrical Q (Qes) | 0.566 |
| Mechanical Q (Qms) | 3.7 |
| Equivalent Volume (Vas) | 62.0 Liters |
| Diaphragm Area (Sd) | 490.9 cm² |
| DC Resistance (Re) | 1.6 Ω |
| Efficiency Bandwidth Product (EBP) | 52.1 |
| Linear Excursion (Xmax) | 9.5 mm |
| Thermal Power (Pe) | 375.0 W |
| Nominal Diameter | 12.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for PowerBass M-1204?
Load Forge's calculated alignment puts PowerBass M-1204 in a 93.0 liter vented enclosure tuned to 23.5 Hz, reaching an F3 cutoff of approximately 22.5 Hz.
Can PowerBass M-1204 be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 57.8 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 44.4 Hz.
What port dimensions should be used for PowerBass M-1204 to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 7.5 cm with a length of 20.4 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if M-1204 fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space