PowerBass S-12TD
Best box: 41.7 L sealed · Fc 51.5 Hz · F3 42.3 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the PowerBass S-12TD against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 12.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the PowerBass S-12TD does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
Textbook Bass Reflex — not recommended (3.9 dB bass hump)
PORT BUILDABLE| Net Box Volume (Vb) | 33.3 Liters |
| Tuning Frequency (Fb) | 31.0 Hz |
| F3 (-3 dB Cutoff) | 46.7 Hz |
| F6 / F10 Extension | 40.0 Hz / 31.8 Hz |
| Port Inner Diameter | Ø 7.5 cm |
| Port Physical Length | 36.0 cm |
| First Pipe Resonance | 478.0 Hz |
| Estimated MOL @ F3 | 111.0 dB SPL |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 0.942 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 1.332; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 41.7 Liters |
| System Q (Qtc) | 1.332 (above Butterworth: Qtc cannot fall below Qts (0.94)) |
| System Resonance (Fc) | 51.5 Hz |
| F3 (-3 dB Cutoff) | 42.3 Hz |
| F6 / F10 Extension | 36.1 Hz / 29.7 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 36.4 Hz |
| Total Q (Qts) | 0.942 |
| Electrical Q (Qes) | 1.194 |
| Mechanical Q (Qms) | 4.46 |
| Equivalent Volume (Vas) | 41.7 Liters |
| Diaphragm Area (Sd) | 530.9 cm² |
| DC Resistance (Re) | 6.5 Ω |
| Efficiency Bandwidth Product (EBP) | 30.5 |
| Linear Excursion (Xmax) | 6.8 mm |
| Thermal Power (Pe) | 300.0 W |
| Nominal Diameter | 12.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for PowerBass S-12TD?
A simple ported box is not recommended for PowerBass S-12TD: the textbook alignment (33.3 liters tuned to 31.0 Hz) needs a 36.0 cm port, and no nearby retune stays buildable without a bass hump. A sealed box, a passive radiator or a folded duct is the practical choice.
Can PowerBass S-12TD be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 41.7 liters with a Qtc of 1.332 (above Butterworth: Qtc cannot fall below Qts (0.94)), the system exhibits an F3 of 42.3 Hz.
What port dimensions should be used for PowerBass S-12TD to avoid port chuffing?
A straight 7.5 cm port would need 36.0 cm of length, which does not fit a practical cabinet. Use a passive radiator or a folded/3D duct instead of a straight tube.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if S-12TD fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space