Tang Band W1-1942S
Best box: 0.05 L sealed · Fc 243.4 Hz · F3 282.8 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Tang Band W1-1942S against your space and targets — instant, no sign-up.
Estimated retail 47.96 USD · Check price & availability ↗
Free, no sign-up to simulate · a free account saves your design
Comparable 1.5" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Tang Band W1-1942S does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Limited linear excursion (Xmax: 1.3 mm); set a high-pass subsonic filter at 25–30 Hz when driven with high power.
Textbook Bass Reflex — not recommended (15.3 dB bass hump)
PORT BUILDABLE| Net Box Volume (Vb) | 1.5 Liters |
| Tuning Frequency (Fb) | 182.1 Hz |
| F3 (-3 dB Cutoff) | 172.3 Hz |
| F6 / F10 Extension | 165.4 Hz / 155.9 Hz |
| Port Inner Diameter | Ø 5.0 cm |
| Port Physical Length | 8.3 cm |
| First Pipe Resonance | 2083.0 Hz |
| Estimated MOL @ F3 | 92.4 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 0.05 Liters |
| System Q (Qtc) | 0.49 (below Butterworth) |
| System Resonance (Fc) | 243.4 Hz |
| F3 (-3 dB Cutoff) | 282.8 Hz |
| F6 / F10 Extension | 201.6 Hz / 142.0 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 120.0 Hz |
| Total Q (Qts) | 0.24 |
| Electrical Q (Qes) | 0.277 |
| Mechanical Q (Qms) | 1.79 |
| Equivalent Volume (Vas) | 0.2 Liters |
| Diaphragm Area (Sd) | 9.0 cm² |
| DC Resistance (Re) | 3.5 Ω |
| Efficiency Bandwidth Product (EBP) | 433.0 |
| Linear Excursion (Xmax) | 1.3 mm |
| Thermal Power (Pe) | 4.0 W |
| Nominal Diameter | 1.5" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Tang Band W1-1942S?
A simple ported box is not recommended for Tang Band W1-1942S: the textbook alignment (1.5 liters tuned to 182.1 Hz) needs a 8.3 cm port, and no nearby retune stays buildable without a bass hump. A sealed box, a passive radiator or a folded duct is the practical choice.
Can Tang Band W1-1942S be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 0.05 liters with a Qtc of 0.49 (below Butterworth), the system exhibits an F3 of 282.8 Hz.
What port dimensions should be used for Tang Band W1-1942S to avoid port chuffing?
A straight 5.0 cm port would need 8.3 cm of length, which does not fit a practical cabinet. Use a passive radiator or a folded/3D duct instead of a straight tube.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if W1-1942S fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space