AudioTechnology 4_h_52_06_13_sd_flexunits_midwoofer
Best box: 10.0 L bass reflex tuned to 54.7 Hz · F3 55.9 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the AudioTechnology 4_h_52_06_13_sd_flexunits_midwoofer against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 5.5" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the AudioTechnology 4_h_52_06_13_sd_flexunits_midwoofer does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Limited linear excursion (Xmax: 3.5 mm); set a high-pass subsonic filter at 25–30 Hz when driven with high power.
Recommended Bass Reflex (Vented)
PORT BUILDABLE| Net Box Volume (Vb) | 10.0 Liters |
| Tuning Frequency (Fb) | 54.7 Hz |
| F3 (-3 dB Cutoff) | 55.9 Hz |
| F6 / F10 Extension | 48.9 Hz / 42.6 Hz |
| Port Inner Diameter | Ø 5.0 cm |
| Port Physical Length | 16.1 cm |
| First Pipe Resonance | 1069.0 Hz |
| Estimated MOL @ F3 | 105.4 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 4.5 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 100.1 Hz |
| F3 (-3 dB Cutoff) | 99.4 Hz |
| F6 / F10 Extension | 75.7 Hz / 57.3 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 48.0 Hz |
| Total Q (Qts) | 0.33 |
| Electrical Q (Qes) | 0.407 |
| Mechanical Q (Qms) | 1.75 |
| Equivalent Volume (Vas) | 16.0 Liters |
| Diaphragm Area (Sd) | 96.0 cm² |
| DC Resistance (Re) | 5.5 Ω |
| Efficiency Bandwidth Product (EBP) | 118.0 |
| Linear Excursion (Xmax) | 3.5 mm |
| Thermal Power (Pe) | 120.0 W |
| Nominal Diameter | 5.5" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for AudioTechnology 4_h_52_06_13_sd_flexunits_midwoofer?
Load Forge's calculated alignment puts AudioTechnology 4_h_52_06_13_sd_flexunits_midwoofer in a 10.0 liter vented enclosure tuned to 54.7 Hz, reaching an F3 cutoff of approximately 55.9 Hz.
Can AudioTechnology 4_h_52_06_13_sd_flexunits_midwoofer be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 4.5 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 99.4 Hz.
What port dimensions should be used for AudioTechnology 4_h_52_06_13_sd_flexunits_midwoofer to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 5.0 cm with a length of 16.1 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if 4_h_52_06_13_sd_flexunits_midwoofer fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space