Bomber MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω
Best box: 17.0 L bass reflex tuned to 62.9 Hz · F3 90.3 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Bomber MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω against your space and targets — instant, no sign-up.
Estimated retail 322.02 EUR · Check price & availability ↗
Free, no sign-up to simulate · a free account saves your design
Comparable 10.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Bomber MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Limited linear excursion (Xmax: 3.5 mm); set a high-pass subsonic filter at 25–30 Hz when driven with high power.
Recommended Bass Reflex (Vented)
PORT BUILDABLE| Net Box Volume (Vb) | 17.0 Liters |
| Tuning Frequency (Fb) | 62.9 Hz |
| F3 (-3 dB Cutoff) | 90.3 Hz |
| F6 / F10 Extension | 75.6 Hz / 58.6 Hz |
| Port Inner Diameter | Ø 6.8 cm |
| Port Physical Length | 11.3 cm |
| First Pipe Resonance | 1519.0 Hz |
| Estimated MOL @ F3 | 117.1 dB SPL |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 0.77 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 1.089; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 21.2 Liters |
| System Q (Qtc) | 1.089 (above Butterworth: Qtc cannot fall below Qts (0.77)) |
| System Resonance (Fc) | 104.7 Hz |
| F3 (-3 dB Cutoff) | 85.4 Hz |
| F6 / F10 Extension | 71.1 Hz / 57.4 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 74.0 Hz |
| Total Q (Qts) | 0.77 |
| Electrical Q (Qes) | 0.806 |
| Mechanical Q (Qms) | 17.26 |
| Equivalent Volume (Vas) | 21.2 Liters |
| Diaphragm Area (Sd) | 353.0 cm² |
| DC Resistance (Re) | 6.38 Ω |
| Efficiency Bandwidth Product (EBP) | 91.8 |
| Linear Excursion (Xmax) | 3.5 mm |
| Thermal Power (Pe) | 600.0 W |
| Nominal Diameter | 10.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Bomber MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω?
Load Forge's calculated alignment puts Bomber MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω in a 17.0 liter vented enclosure tuned to 62.9 Hz, reaching an F3 cutoff of approximately 90.3 Hz.
Can Bomber MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 21.2 liters with a Qtc of 1.089 (above Butterworth: Qtc cannot fall below Qts (0.77)), the system exhibits an F3 of 85.4 Hz.
What port dimensions should be used for Bomber MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 6.8 cm with a length of 11.3 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if MEDIO GRAVE 10″ COPPER RING 600 WATTS RMS 8Ω fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space