Goldwood GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm
Best box: 9.9 L sealed · Fc 64.5 Hz · F3 39.8 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Goldwood GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm against your space and targets — instant, no sign-up.
Estimated retail 42.98 USD · Check price & availability ↗
Free, no sign-up to simulate · a free account saves your design
Comparable 6.5" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Goldwood GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Port length (45.9 cm) exceeds a straight internal run; use an elbow bend, slotted vent or 3D folded duct to fit the enclosure.
Textbook Bass Reflex — not recommended (7.1 dB bass hump)
PORT NEEDS ELBOW / 3D| Net Box Volume (Vb) | 7.9 Liters |
| Tuning Frequency (Fb) | 38.8 Hz |
| F3 (-3 dB Cutoff) | 49.0 Hz |
| F6 / F10 Extension | 43.5 Hz / 36.1 Hz |
| Port Inner Diameter | Ø 5.0 cm |
| Port Physical Length | 45.9 cm |
| First Pipe Resonance | 375.0 Hz |
| Estimated MOL @ F3 | 101.9 dB SPL |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 0.88 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 1.245; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 9.9 Liters |
| System Q (Qtc) | 1.245 (above Butterworth: Qtc cannot fall below Qts (0.88)) |
| System Resonance (Fc) | 64.5 Hz |
| F3 (-3 dB Cutoff) | 39.8 Hz |
| F6 / F10 Extension | 34.6 Hz / 29.0 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 45.6 Hz |
| Total Q (Qts) | 0.88 |
| Electrical Q (Qes) | 0.99 |
| Mechanical Q (Qms) | 7.95 |
| Equivalent Volume (Vas) | 9.9 Liters |
| Diaphragm Area (Sd) | 136.4 cm² |
| DC Resistance (Re) | 3.7 Ω |
| Efficiency Bandwidth Product (EBP) | 46.1 |
| Linear Excursion (Xmax) | 4.0 mm |
| Thermal Power (Pe) | 140.0 W |
| Nominal Diameter | 6.5" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Goldwood GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm?
A simple ported box is not recommended for Goldwood GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm: the textbook alignment (7.9 liters tuned to 38.8 Hz) needs a 45.9 cm port, and no nearby retune stays buildable without a bass hump. A sealed box, a passive radiator or a folded duct is the practical choice.
Can Goldwood GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 9.9 liters with a Qtc of 1.245 (above Butterworth: Qtc cannot fall below Qts (0.88)), the system exhibits an F3 of 39.8 Hz.
What port dimensions should be used for Goldwood GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm to avoid port chuffing?
A straight 5.0 cm port would need 45.9 cm of length, which does not fit a practical cabinet. Use a passive radiator or a folded/3D duct instead of a straight tube.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if GW-6PC-4 6-1/2" Heavy Duty Woofer 4 Ohm fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space