Infinity BETA TEN
Best box: 11.4 L bass reflex tuned to 45.0 Hz · F3 60.4 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Infinity BETA TEN against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 10.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Infinity BETA TEN does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- The textbook alignment (11.4 L at 42.9 Hz) would need a 105.1 cm port; the recommendation is retuned to 11.4 L at 45.0 Hz so the port can be built.
- Port length (94.8 cm) exceeds a straight internal run; use an elbow bend, slotted vent or 3D folded duct to fit the enclosure.
Recommended Bass Reflex (Vented)
PORT NEEDS ELBOW / 3D| Net Box Volume (Vb) | 11.4 Liters |
| Tuning Frequency (Fb) | 45.0 Hz |
| F3 (-3 dB Cutoff) | 60.4 Hz |
| F6 / F10 Extension | 49.5 Hz / 41.0 Hz |
| Port Inner Diameter | Ø 10.0 cm |
| Port Physical Length | 94.8 cm |
| First Pipe Resonance | 181.0 Hz |
| Estimated MOL @ F3 | 110.3 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 6.7 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 83.2 Hz |
| F3 (-3 dB Cutoff) | 86.4 Hz |
| F6 / F10 Extension | 66.9 Hz / 51.3 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 24.0 Hz |
| Total Q (Qts) | 0.2 |
| Electrical Q (Qes) | 0.205 |
| Mechanical Q (Qms) | 8.08 |
| Equivalent Volume (Vas) | 77.0 Liters |
| Diaphragm Area (Sd) | 346.0 cm² |
| DC Resistance (Re) | 2.8 Ω |
| Efficiency Bandwidth Product (EBP) | 117.0 |
| Linear Excursion (Xmax) | 10.0 mm |
| Thermal Power (Pe) | 250.0 W |
| Nominal Diameter | 10.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Infinity BETA TEN?
Load Forge's calculated alignment puts Infinity BETA TEN in a 11.4 liter vented enclosure tuned to 45.0 Hz, reaching an F3 cutoff of approximately 60.4 Hz.
Can Infinity BETA TEN be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 6.7 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 86.4 Hz.
What port dimensions should be used for Infinity BETA TEN to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 10.0 cm with a length of 94.8 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if BETA TEN fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space