Reckhorn D-250
Best box: 56.2 L bass reflex tuned to 29.2 Hz · F3 27.8 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Reckhorn D-250 against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 10.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Reckhorn D-250 does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- The textbook alignment (48.9 L at 24.3 Hz) would need a 172.7 cm port; the recommendation is retuned to 56.2 L at 29.2 Hz so the port can be built.
- Xmax is not published, so the port size is an empirical estimate (area ≥ 12 in² per ft³ of net volume, minimum by driver size), not a displacement calculation. Check air velocity in Load Forge Studio.
- Port length (99.8 cm) exceeds a straight internal run; use an elbow bend, slotted vent or 3D folded duct to fit the enclosure.
Recommended Bass Reflex (Vented)
PORT NEEDS ELBOW / 3D| Net Box Volume (Vb) | 56.2 Liters |
| Tuning Frequency (Fb) | 29.2 Hz |
| F3 (-3 dB Cutoff) | 27.8 Hz |
| F6 / F10 Extension | 25.2 Hz / 22.3 Hz |
| Port Inner Diameter ESTIMATED | Ø 15.0 cm |
| Port Physical Length | 99.8 cm |
| First Pipe Resonance | 172.0 Hz |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 21.6 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 45.0 Hz |
| F3 (-3 dB Cutoff) | 46.8 Hz |
| F6 / F10 Extension | 35.6 Hz / 27.1 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 22.0 Hz |
| Total Q (Qts) | 0.341 |
| Electrical Q (Qes) | 0.378 |
| Mechanical Q (Qms) | 3.48 |
| Equivalent Volume (Vas) | 71.4 Liters |
| Diaphragm Area (Sd) | 350.0 cm² |
| DC Resistance (Re) | 3.6 Ω |
| Efficiency Bandwidth Product (EBP) | 58.2 |
| Linear Excursion (Xmax) | N/A mm |
| Thermal Power (Pe) | N/A W |
| Nominal Diameter | 10.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Reckhorn D-250?
Load Forge's calculated alignment puts Reckhorn D-250 in a 56.2 liter vented enclosure tuned to 29.2 Hz, reaching an F3 cutoff of approximately 27.8 Hz.
Can Reckhorn D-250 be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 21.6 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 46.8 Hz.
What port dimensions should be used for Reckhorn D-250 to avoid port chuffing?
Xmax is not published for Reckhorn D-250, so the port is an empirical estimate: a 15.0 cm diameter with a length of 99.8 cm (area at least 12 in² per ft³ of net volume). Check the air velocity at your power level in Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if D-250 fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space