SB Acoustics Satori MR13P-4 Bass-midwoofer
Best box: 0.083 L sealed · Fc 126.0 Hz · F3 119.2 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the SB Acoustics Satori MR13P-4 Bass-midwoofer against your space and targets — instant, no sign-up.
Free, no sign-up to simulate · a free account saves your design
Comparable 8.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the SB Acoustics Satori MR13P-4 Bass-midwoofer does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Port length (90.4 cm) exceeds a straight internal run; use an elbow bend, slotted vent or 3D folded duct to fit the enclosure.
- Limited linear excursion (Xmax: 3.0 mm); set a high-pass subsonic filter at 25–30 Hz when driven with high power.
Textbook Bass Reflex — not recommended (6.9 dB bass hump)
PORT NEEDS ELBOW / 3D| Net Box Volume (Vb) | 1.5 Liters |
| Tuning Frequency (Fb) | 64.6 Hz |
| F3 (-3 dB Cutoff) | 60.7 Hz |
| F6 / F10 Extension | 57.7 Hz / 53.7 Hz |
| Port Inner Diameter | Ø 5.0 cm |
| Port Physical Length | 90.4 cm |
| First Pipe Resonance | 190.0 Hz |
| Estimated MOL @ F3 | 91.8 dB SPL |
Recommended Sealed (Acoustic Suspension)
MAX TRANSIENT DAMPING| Net Box Volume (Vb) | 0.083 Liters |
| System Q (Qtc) | 0.707 (Butterworth) |
| System Resonance (Fc) | 126.0 Hz |
| F3 (-3 dB Cutoff) | 119.2 Hz |
| F6 / F10 Extension | 91.9 Hz / 69.8 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 41.0 Hz |
| Total Q (Qts) | 0.23 |
| Electrical Q (Qes) | 0.251 |
| Mechanical Q (Qms) | 2.8 |
| Equivalent Volume (Vas) | 0.7 Liters |
| Diaphragm Area (Sd) | 220.0 cm² |
| DC Resistance (Re) | 3.3 Ω |
| Efficiency Bandwidth Product (EBP) | 163.6 |
| Linear Excursion (Xmax) | 3.0 mm |
| Thermal Power (Pe) | 30.0 W |
| Nominal Diameter | 8.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for SB Acoustics Satori MR13P-4 Bass-midwoofer?
A simple ported box is not recommended for SB Acoustics Satori MR13P-4 Bass-midwoofer: the textbook alignment (1.5 liters tuned to 64.6 Hz) needs a 90.4 cm port, and no nearby retune stays buildable without a bass hump. A sealed box, a passive radiator or a folded duct is the practical choice.
Can SB Acoustics Satori MR13P-4 Bass-midwoofer be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 0.083 liters with a Qtc of 0.707 (Butterworth), the system exhibits an F3 of 119.2 Hz.
What port dimensions should be used for SB Acoustics Satori MR13P-4 Bass-midwoofer to avoid port chuffing?
A straight 5.0 cm port would need 90.4 cm of length, which does not fit a practical cabinet. Use a passive radiator or a folded/3D duct instead of a straight tube.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if Acoustics Satori MR13P-4 Bass-midwoofer fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space