Skar Audio TXL-18 D1
Best box: 67.5 L bass reflex tuned to 36.3 Hz · F3 49.4 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Skar Audio TXL-18 D1 against your space and targets — instant, no sign-up.
Estimated retail 469.99 USD · Check price & availability ↗
Free, no sign-up to simulate · a free account saves your design
Comparable 18.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Skar Audio TXL-18 D1 does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- The textbook alignment (67.5 L at 34.6 Hz) would need a 102.2 cm port; the recommendation is retuned to 67.5 L at 36.3 Hz so the port can be built.
- Port length (91.6 cm) exceeds a straight internal run; use an elbow bend, slotted vent or 3D folded duct to fit the enclosure.
Recommended Bass Reflex (Vented)
PORT NEEDS ELBOW / 3D| Net Box Volume (Vb) | 67.5 Liters |
| Tuning Frequency (Fb) | 36.3 Hz |
| F3 (-3 dB Cutoff) | 49.4 Hz |
| F6 / F10 Extension | 40.4 Hz / 31.2 Hz |
| Port Inner Diameter | Ø 20.0 cm |
| Port Physical Length | 91.6 cm |
| First Pipe Resonance | 188.0 Hz |
| Estimated MOL @ F3 | 127.5 dB SPL |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 0.67 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 0.948; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 84.4 Liters |
| System Q (Qtc) | 0.948 (above Butterworth) |
| System Resonance (Fc) | 57.6 Hz |
| F3 (-3 dB Cutoff) | 50.6 Hz |
| F6 / F10 Extension | 40.8 Hz / 32.2 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 40.7 Hz |
| Total Q (Qts) | 0.67 |
| Electrical Q (Qes) | 0.756 |
| Mechanical Q (Qms) | 5.87 |
| Equivalent Volume (Vas) | 84.4 Liters |
| Diaphragm Area (Sd) | 1229.0 cm² |
| DC Resistance (Re) | 2.0 Ω |
| Efficiency Bandwidth Product (EBP) | 53.8 |
| Linear Excursion (Xmax) | 17.0 mm |
| Thermal Power (Pe) | 5000.0 W |
| Nominal Diameter | 18.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Skar Audio TXL-18 D1?
Load Forge's calculated alignment puts Skar Audio TXL-18 D1 in a 67.5 liter vented enclosure tuned to 36.3 Hz, reaching an F3 cutoff of approximately 49.4 Hz.
Can Skar Audio TXL-18 D1 be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 84.4 liters with a Qtc of 0.948 (above Butterworth), the system exhibits an F3 of 50.6 Hz.
What port dimensions should be used for Skar Audio TXL-18 D1 to avoid port chuffing?
Sized from cone displacement (Sd × Xmax), a minimum port diameter of 20.0 cm with a length of 91.6 cm is suggested; check the port air velocity at your drive level in the Load Forge Studio.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if TXL-18 D1 fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space