Visaton R 10 S - 8 Ohm
Best box: 1.7 L sealed · Fc 226.3 Hz · F3 201.5 Hz
Open and tweak this box live ↗
Will it fit your requirements?
Check the Visaton R 10 S - 8 Ohm against your space and targets — instant, no sign-up.
Estimated retail 8.28 EUR · Check price & availability ↗
Free, no sign-up to simulate · a free account saves your design
Comparable 4.0" Drivers
Drivers with similar piston area, resonance and Qts — useful alternatives when the Visaton R 10 S - 8 Ohm does not fit your target box volume or tuning. Each entry links to its full enclosure design and Thiele/Small parameters.
⚠️ Engineering Notice for Builders
- Limited linear excursion (Xmax: 1.5 mm); set a high-pass subsonic filter at 25–30 Hz when driven with high power.
Textbook Bass Reflex — not recommended (7.9 dB bass hump)
PORT BUILDABLE| Net Box Volume (Vb) | 1.5 Liters |
| Tuning Frequency (Fb) | 136.0 Hz |
| F3 (-3 dB Cutoff) | 229.5 Hz |
| F6 / F10 Extension | 209.0 Hz / 181.7 Hz |
| Port Inner Diameter | Ø 5.0 cm |
| Port Physical Length | 17.6 cm |
| First Pipe Resonance | 975.0 Hz |
| Estimated MOL @ F3 | 106.6 dB SPL |
Sealed (Acoustic Suspension) — compromise
SUITS INFINITE / OPEN BAFFLEWith Qts 1.99 a Butterworth (Qtc 0.707) box would be many times Vas. A box equal to Vas reaches Qtc 2.814; for a flat response this driver is better used on an infinite (IB) or open baffle.
| Net Box Volume (Vb) | 1.7 Liters |
| System Q (Qtc) | 2.814 (above Butterworth: Qtc cannot fall below Qts (1.99)) |
| System Resonance (Fc) | 226.3 Hz |
| F3 (-3 dB Cutoff) | 201.5 Hz |
| F6 / F10 Extension | 183.4 Hz / 161.0 Hz |
| Air Spring Linearity | High (Zero port compression) |
Thiele/Small Parameters
| Resonance (Fs) | 160.0 Hz |
| Total Q (Qts) | 1.99 |
| Electrical Q (Qes) | 2.915 |
| Mechanical Q (Qms) | 6.27 |
| Equivalent Volume (Vas) | 1.7 Liters |
| Diaphragm Area (Sd) | 56.0 cm² |
| DC Resistance (Re) | 7.2 Ω |
| Efficiency Bandwidth Product (EBP) | 54.9 |
| Linear Excursion (Xmax) | 1.5 mm |
| Thermal Power (Pe) | 20.0 W |
| Nominal Diameter | 4.0" |
| Catalog Source | Load Forge catalog (manufacturer datasheets and retailer listings) |
Frequently Asked Questions
What is the recommended ported (bass reflex) box volume for Visaton R 10 S - 8 Ohm?
A simple ported box is not recommended for Visaton R 10 S - 8 Ohm: the textbook alignment (1.5 liters tuned to 136.0 Hz) needs a 17.6 cm port, and no nearby retune stays buildable without a bass hump. A sealed box, a passive radiator or a folded duct is the practical choice.
Can Visaton R 10 S - 8 Ohm be used in a sealed box?
Yes. In a sealed (acoustic suspension) enclosure of 1.7 liters with a Qtc of 2.814 (above Butterworth: Qtc cannot fall below Qts (1.99)), the system exhibits an F3 of 201.5 Hz.
What port dimensions should be used for Visaton R 10 S - 8 Ohm to avoid port chuffing?
A straight 5.0 cm port would need 17.6 cm of length, which does not fit a practical cabinet. Use a passive radiator or a folded/3D duct instead of a straight tube.
Shareable Acoustic Card for Forums & Social Media
Embed this design card on DIYAudio, AVSForum, Reddit, or Facebook. It shows the calculated F3, MOL (when the power rating is published) and box parameters.
Not sure if R 10 S - 8 Ohm fits your physical space?
Don't force a driver into the wrong box. Use Bass Match to calculate which of 8,000+ catalog drivers delivers the highest SPL, lowest F3, and cleanest port air velocity for your exact trunk or room dimensions.
Run Bass Match for Your Space